مستخدم:Nouf2013/ملعب

من ويكيبيديا، الموسوعة الحرة

حصاد الطاقة هي العملية التي من خلالها الـطاقة تُستَمد من مصادر خارجية (مثال: الـطاقة شمسية، الـطاقة حرارية، الـطاقة ريحية والـطاقة حركية )، تُجمع وتخزَن في أجهزة صغيرة لاسلكية مستقلة، كالموجودة في الإلكترونيات الملبوسة (wearable electronics) وشبكات استشعار لاسلكية.

هذه الحصادات تزوَد بكمية قليلة من الطاقة لالكترونياتها المنخفضة الطاقه. بينما الوقود المدخل في بعض المولدات الكبيرة الحجم تكلف اموال (نفط، فحم، ..الخ)، مصدر الطاقة للحصادات ظاهره في الخلفيه المحيطة وهي مجانية. على سبيل المثال: تدرجات الحرارة موجودة من تشغيل محرك الاحتراق وفي المناطق الحضارية، هناك كمية كبيره من الطاقة الكهرومغناطيسية في البيئه بسبب البث الإذاعي والتلفزيوني.

التشغيل[عدل]

أجهزة حصاد الطاقة تحول الطاقة المحيطة إلى طاقة كهربائية التي جذبت كثير من الإهتمام في القطاعين العسكري والتجاري. بعض الأنظمة تحول الحركة (مثل أمواج المحيط) إلى كهرباء كي تستخدم من قبل أجهزة استشعار ومراقبة المحيط للتشغيل المستقل. التطبيقات المستقبلية قد تحتوي على أجهزة تخرج طاقة عالية (أو صفوف من هذه الأجهزة) تنشر في مواقع بعيدة كمحطات طاقة معتمدة لتخدم أنظمة كبيرة. تطبيق آخر هو الذي في الإلكترونيات الملبوسة, حيث أجهزة حصاد الطاقة تستطيع تشحن أو تعيد شحن الهواتف المحمولة، الحواسيب المحمولة، معدات اتصال الراديو ..الخ. كل هذه الأخهزه يجب أن تكون قوية بما فيه الكفايه لتتحمل على المدى الطويل التعرض إلى بيئة معادية متقلبة ولها نطاق واسع من الحساسية الديناميكية لاستغلال النطاق الكامل للحركة الموجيه.

تراكم الطاقة[عدل]

ويمكن أيضاً أن تحصد الطاقة لشحن أجهزه استشعار الصغيرة المستقلة كتلك التي تم تطويرها باستخدام تقنية MEMS. هذه الأنظمة تكون غالباً صغيرة جداً وتحتاج طاقة قليلة، لكن تطبيقاتها محدودة بالإعتماد على طاقة البطارية. الطاقة من الذبذبات المحيطة, الرياح, الحرارةأو الضوء قد تمكن أجهزة الاستشعار الذكية لكي تعمل إلى مالا نهايه. وشاركت العديد من الفئات الأكاديمية والتجارية في تحليل وتطوير تكنولوجيا حصاد الطاقه العاملة بالإهتزاز, منها فريق التحكم والطاقة وفريق أجهزة البصريات وأشباه الموصلات في إمبريال كوليدج لندن، مركز الالكترونيات الدقيقة IMEC وشريكه مركز هولست ,[1] الطاقة المتكيفه, ARVENI, معهد ماساتشوستس للتقنية بوستون, معهد جورجيا التقني, جامعة كاليفورنيا في بركلي, جامعة ساوثهامبتون, جامعة بريستول,[2] جامعة نانياج التكنولوجية,[3] PMG Perpetuum, جامعة فيستفولد, جامعة سنغافورة الوطنية,[4] مختبر NiPS في جامعة بيروجيا,[5] جامعة كولومبيا,[6] جامعة برشلونه المستقلة و USN ومختبر الطاقة المتجددة في جامعة اولسان (اولسان, كوريا الجنوبية). المؤسسة الوطنية للعلوم أيضا تدعم مصنع / جامعة مركز البحوث التعاونية برئاسة جامعة فرجينيا للتقنية و جامعة تكساس في دالاس تسمى بمركز مواد حصاد الطاقة والأنظمة.

كثافة الطاقة القياسية المتوفرة في أجهزة حصاد الطاقة تعتمد اعتماداً كبيراً على تطبيق معين (تتأثر بحجم المولد) والتصميم نفسه لمولد الحصاد. بشكل عام، لأجهزة الطاقة الحركية، القيم القياسية هي عدد قليل من μW / سم ³ لتطبيقات طاقة جسم الإنسان ومئات من μW / سم ³ لمولدات الطاقة من الآلات.[7] معظم أجهزة طاقة المسح للالكترونيات الملبوسه تنتج طاقة قليلة.[8][تحقق من المصدر]

تخزين الطاقة[عدل]

بشكل عام, الطاقة يمكن أن تخزن في مكثف, المكثف القوي, or البطارية. تستخدم المكثفات عندما يحتاج التطبيق لتوفير طاقة ضخمة. البطاريات تسرب كميات أقل من الطاقة، وتستخدم بالتالي عندما يكون الجهاز في حاجة إلى توفير تدفق مستمر من الطاقة.

استخدامات الطاقة[عدل]

الاهتمام الحالي للحصاد المنخفض الطاقة لشبكات الاستشعار مستقلة. في هذه التطبيقات مخطط حصاد الطاقة يضع الطاقة المخزنة في مكثف ثم تعزيز/تنظيم إلى مكثف تخزين آخر أو بطارية لاستخدامها في معالج دقيق.[9] الطاقة عادة تستخدم في تطبيقات جهاز الاستشعار والبيانات تخزن أو يمكن أن تبث بالطريقة اللاسلكية.[10]

الدافع[عدل]

تاريخ حصاد الطاقة يعود إلى طواحين الهواء والسقاية. لقد بحث الناس عن طرق لتخزين الطاقة من الحرارة والذبذبات لعدة عقود. احداها كان القوة الدافعة وراء البحث عن أجهزة جديدة لحصاد الطاقة وهو الرغبة في شحن شبكات الاستشعار والأجهزة النقالة بدون بطاريات. حصاد الطاقة هو دافع للرغبة في معالجة مسألة تغير المناح والاحتباس الحراري.

الأجهزة[عدل]

هناك العديد من مصادر الطاقة ذات النطاق الصغير التي بشكل عام لايمكن أن تصل إلى مستوى الحجم الصناعي:

  • بعض ساعة يد تشحن بطاقة حركية (تدعى بـالساعة الاوتماتيكية), في هذه الحالة حركة الذراع هي المستخدمة. حركة الذراع تسبب في دوران النابض. أحدث تصميم قدمتها سيكو ("الحركية") تستخدم حركة المغناطيس في المولد الكهرومغناطيسي بدلا من شحن حركة الكوارتز. الحركة تنتج معدل تغير التدفق، والتي تنتج في بعض المجالات الكهرومغناطيسية الناجمة عن اللفائف. المفهوم يرتبط ببساطة لـقانون فاراداي.
  • لوح ضوئي هي طريقة لتوليد الطاقة الكهربائية عن طريق تحويل الأشعة الشمسية (في الداخل والخارج) إلى كهرباء مباشرة باستخدام اشباة الموصلات التي تظهر الأثر الضوئي. توليد طاقة الألواح الشمسية توظف الألواح الشمسية التي تتألف من عدد من الخلايا تحتوي على مواد ضوئية.
  • المولدات الكهروحرارية تتكون بوصل اثنين من المواد المختلفة بوجود التدرج الحراري. الجهد الكبير الناتج أمر ممكن من خلال ربط العديد من الوصلات الكهربائية في سلسلة وحراريا بشكل متوازي. الأداء القياسي هو 100-200 μV / K لكل وصلة. ويمكن استخدامها لالتقاط mW.s من الطاقة من المعدات الصناعية والهياكل وحتى من جسم الإنسان. مقترنة ببعضها عادة بالمغاسل الحارة لتحسين التدرج في درجة الحرارة.
  • توربين الرياح الصغيرة تستخدم لجني طاقة الريح متاحة بسهولة في البيئة على شكل طاقة حركية لشحن الأجهزة الالكترونية ذات الطاقة المنخفضة مثل عقد أجهزة الاستشعار اللاسلكية. عندما ينساب الهواء عبر شفرات التوربين, فرق الضغط الصافي يظهر بين سرعة الريح فوق وتحت الشفرات. وهذا يؤدي إلى توليد قوة الرفع والتي بدورها تقوم بتدوير الشفرات.
  • الكريستالات أو الألياف الـكهروضغطية تولد جهد قليل مهما تحولت وتشكلت ميكانيكياً. الذبذبات من المحركات يمكنها تنشيط المواد الكهروضغطية, كما يستطيع فعله كعب الحذاء.
  • الهوائيات الخاصة يمكنها جمع الطاقة من موجات الراديو [11] أو من الناحية النظرية تردد أعلى موجة كهرومغناطيسية. [بحاجة لمصدر]
  • الطاقة من المفاتيح المضغوطه خلال استخدام الأجهزة الالكترونيه المحمولة أو جهاز التحكم عن بعد, باستخدام مغناطيس ولفافه أو محولات الطاقة الكهروضغطية, بالإمكان استخدامها للمساعدة في شحن الجهاز.[12]

مصادر الإشعاع المحيطة[عدل]

مصدر الطاقة المحتملة تأتي من أجهزة البث الإذاعي المنتشرة. تاريخياً, سواء كانت منطقة جمع كبيرة أو قريبة من إشعاع مصدر الطاقة اللاسلكية فإنها لازمه لأخذ طاقة مفيده من هذا المصدر. هوائي النانو هو تطوير مقترح التي بالامكان التغلب على هذا القيد بالاستفادة من الاشعاع الطبيعي الوفير (مثل أشعة الشمس).

احدى الأفكار ان يبث طاقة تردد الراديو لشحن الأجهزة البعيدة: هذا الآن شائع في أنظمة تحديد تردد الراديو السلبيه، لكن الأمان وهيئة الاتصالات الفيدراليةالأمريكية FCC (ومايكافئها في جميع انحاء العالم) حددوا الطاقة القصوى التي يمكن أن تبث بهذه الطريقة للاستخدام المدني.

حصاد الميكانيكا الحيوية[عدل]

حاصدات طاقة الميكانيكا الحيوية أيضاً تتم انشائها. احدى النماذج الحالية هو حصاد طاقة الميكانيكا الحيوية لـماكس دونلان التي تربط حول الركبة.[13] الأجهزة التي تماثلها تسمح بتوليد 2,5 واط من الطاقة للركبة. هذا كافي لشحن 5 هواتف خلوية. كرة القدم (Soccket) يمكنها توليد وحفظ 6 واط.[14]

الحصاد الضوئي[عدل]

تكنولوجيا حصاد الطاقة الضوئية اللاسلكية يقدم مزايا هامة مقارنة بالسلكية أو حلول أجهزه الاستشعار تعمل بالبطارية: المصادر الفعليه التي لاتنضب من الطاقة تأثيرات البيئه المعادية فيها قليلة أو معدومة. حلول الحصاد الضوئي الداخلي إلى الآن يشحن بالسيليكون الغير متبلور بضبط خاص (aSi) وهي تكنولوجيا تستخدم كثيراً في الآت الحساب الشمسية. في السنوات الأخيرة التكنولوجيات الضوئيه الجديدة اصبحت في صدارة حصاد الطاقة مثل خلايا التحسس الصبغي الشمسي. الأصباغ تمتص الضوء مثل ما يفعله الكلوروفيل في النباتات. تتحرر الالكترونات بهروب مفاجئ من طبقة TiO2 ومن ثم تبدأ بالانتشار خلال محلول كهربي, إذا الصبغة أمكن ضبطها إلى الطيف المرئي فإنها تنتج طاقة أكبر. عند 200 لكس فإن خلايا التحسس الصبغي الشمسي يمكن أن تزود أعلى من 15 µW لكل سم².

جهاز التحكم عن بعد بدون بطارية من ارفيني لشركة فيليبس

حصاد الطاقة الكهروضغطية[عدل]

التأثير الكهروضغطي تحول الانفعال الميكانيكي إلى تيار كهربائي أو جهد. الانفعال يمكن أن يأتي من مصادر مختلفة. حركة الإنسان، ذبذبات الزلازال المنخفضه, والضوضاء أمثلة في الحياة اليومية. ماعدا في الحلات النادرة التأثير الكهروضغطي التي تعمل في المكيفات تحتاج مدخلات متفاوتة الوفت في الرنين الميكانيكي لتكون فعاله.

معظم مصادر الكهرباء الكروضغطية تنتج طاقة بناء على الميللي واط، صغيرة جداً على تطبيقات النظام، لكنها كافية للأجهزة المحمولة باليد مثل بعض ساعات اليد الذاتية الدوران الموجودة تجارياً. احدى الاقتراحات أن تستخدم للأجهزة الدقيقة الحجم، كالتي في جهاز حصاد الطاقة الهيدروليكية الدقيقة. في هذا الجهاز، تدفق السوائل الهيدروليكية المضغوطة يدفع المكبس التبادلي مدعومة بثلاث عناصر كهروضغطية التي تحول تقلبات الضغط إلى تيار بديل.

حصاد الطاقة الكهروضغطية تم التحقيق فيها في أواخر التسعينيات, فإنها بقيت تكنولوجيا ناشئه. بالرغم من ذلك بعض التطورات المثيرة للإهتمام صُنعت في المفتاح الالكتروني ذاتي الشحن في INSA للهندسه , تنفذها Arveni العرضية. في 2006، اثبات مفهوم زر الباب اللاسلكي بدون بطارية قد تم، ومؤخراً، أظهرت دراسة أن جهاز التحكم عن بعد التقليدي يمكن أن يشحن بالحصاد الكهروضغطي. التطبيقات الصناعية الأخرى ظهرت بين عامي 2000 و2005,[15] لحصد الطاقة على سبيل المثال من أجهزة الاستشعار والاهتزاز أو من صدمة.

الأنظمة الكهروضغطية يمكنها تحويل الحركة من جسم الانسان إلى طاقة كهربائية. داربا موَلَت الجهود لاستغلال الطاقة من حركة الذراع والأرجل، أثر الحذاء، وضغط الدم مقابل طاقة منخفضة لأجهزة استشعار مزروعة أو ملبوسة. فرشاة النانو لـ د.زونج لين وانج مثال آخر لحصاد الطاقة الكهروضغطية.[16] يمكن دمجها في الملابس. تحتاج إلى تصميم دقيق لتقليل عدم راحة المستخدم. مصادر حصاد الطاقة المرتبطة لها أثر على الجسم. مشروع جامع الطاقة الاهتزازية[17] مشروع آخر تم اعداده لمحاولة جمع الطاقه الكهربائية من الذبذبات والتحركات البيئية. الحزام الدقيق لـوانج سودونج يمكن استخدامه لجمع الكهرباء من التنفس.[18] وأخيراً، حصاد الطاقة الكهروضغطية ذو حجم ميلميتري تم انشائه مسبقاُ.[19]

The use of piezoelectric materials to harvest power has already become popular. Piezoelectric materials have the ability to transform mechanical strain energy into electrical charge. Piezo elements are being embedded in walkways[20][21][22] to recover the "people energy" of footsteps. They can also be embedded in shoes[23] to recover "walking energy". Researchers at MIT developed the first micro-scale piezoelectric energy harvester using thin film PZT in 2005.[24] Arman Hajati and Sang-Gook Kim invented the Ultra Wide-Bandwidth micro-scale piezoelectric energy harvesting device by exploiting the nonlinear stiffness of a doubly clamped microelectromechanical systems (MEMSs) resonator. The stretching strain in a doubly clamped beam shows a nonlinear stiffness, which provides a passive feedback and results in amplitude-stiffened Duffing mode resonance.[25]

Pyroelectric energy harvesting[عدل]

The pyroelectric effect converts a temperature change into electric current or voltage. It is analogous to the piezoelectric effect, which is another type of ferroelectric behavior. Pyroelectricity requires time-varying inputs and suffers from small power outputs in energy harvesting applications due to its low operating frequencies. However, one key advantage of pyroelectrics over thermoelectrics is that many pyroelectric materials are stable up to 1200 ⁰C or higher, enabling energy harvesting from high temperature sources and thus increasing thermodynamic efficiency.

One way to directly convert waste heat into electricity is by executing the Olsen cycle on pyroelectric materials. The Olsen cycle consists of two isothermal and two isoelectric field processes in the electric displacement-electric field (D-E) diagram. The principle of the Olsen cycle is to charge a capacitor via cooling under low electric field and to discharge it under heating at higher electric field. Several pyroelectric converters have been developed to implement the Olsen cycle using conduction,[26] convection,[27][28][29][30] or radiation.[31] It has also been established theoretically that pyroelectric conversion based on heat regeneration using an oscillating working fluid and the Olsen cycle can reach Carnot efficiency between a hot and a cold thermal reservoir.[32] Moreover, recent studies have established polyvinylidene fluoride trifluoroethylene [P(VDF-TrFE)] polymers [33] and lead lanthanum zirconate titanate (PLZT) ceramics [34] as promising pyroelectric materials to use in energy converters due to their large energy densities generated at low temperatures. Additionally, a pyroelectric scavenging device that does not require time-varying inputs was recently introduced. The energy-harvesting device uses the edge-depolarizing electric field of a heated pyroelectric to convert heat energy into mechanical energy instead of drawing electric current off two plates attached to the crystal-faces.[35]

Thermoelectrics[عدل]

In 1821, Thomas Johann Seebeck discovered that a thermal gradient formed between two dissimilar conductors produces a voltage. At the heart of the thermoelectric effect is the fact that a temperature gradient in a conducting material results in heat flow; this results in the diffusion of charge carriers. The flow of charge carriers between the hot and cold regions in turn creates a voltage difference. In 1834, Jean Charles Athanase Peltier discovered that running an electric current through the junction of two dissimilar conductors could, depending on the direction of the current, cause it to act as a heater or cooler. The heat absorbed or produced is proportional to the current, and the proportionality constant is known as the Peltier coefficient. Today, due to knowledge of the Seebeck and Peltier effects, thermoelectric materials can be used as heaters, coolers and generators (TEGs).

Ideal thermoelectric materials have a high Seebeck coefficient, high electrical conductivity, and low thermal conductivity. Low thermal conductivity is necessary to maintain a high thermal gradient at the junction. Standard thermoelectric modules manufactured today consist of P- and N-doped bismuth-telluride semiconductors sandwiched between two metallized ceramic plates. The ceramic plates add rigidity and electrical insulation to the system. The semiconductors are connected electrically in series and thermally in parallel.

Miniature thermocouples have been developed that convert body heat into electricity and generate 40μW at 3V with a 5 degree temperature gradient, while on the other end of the scale, large thermocouples are used in nuclear RTG batteries.

Practical examples are the finger-heartratemeter by the Holst Centre and the thermogenerators by the Fraunhofer Gesellschaft.[36][37]

Advantages to thermoelectrics:

  1. No moving parts allow continuous operation for many years. Tellurex Corporation[38] (a thermoelectric production company) claims that thermoelectrics are capable of over 100,000 hours of steady state operation.
  2. Thermoelectrics contain no materials that must be replenished.
  3. Heating and cooling can be reversed.

One downside to thermoelectric energy conversion is low efficiency (currently less than 10%). The development of materials that are able to operate in higher temperature gradients, and that can conduct electricity well without also conducting heat (something that was until recently thought impossible), will result in increased efficiency.

Future work in thermoelectrics could be to convert wasted heat, such as in automobile engine combustion, into electricity.

Electrostatic (capacitive) energy harvesting[عدل]

This type of harvesting is based on the changing capacitance of vibration-dependent varactors. Vibrations separate the plates of an initially charged varactor (variable capacitor), and mechanical energy is converted into electrical energy. An example of an electrostatic energy harvester with embedded energy storage is the M2E Power Kinetic Battery. Another example is CSIRO’s Flexible Integrated Energy Device (FIED)[39] Yet another example is the Tremont Electric nPower PEG.[40] Finally, there is the Regenerative shock absorber.

Electrostatic energy harvesters need a polarization source to work and to convert mechanical energy from vibrations into electricity. The polarization source should be in the order of some hundreds of volts ; this greatly complicates the power management circuit. Another solution consists in using electrets, that are electrically charged dielectrics able to keep the polarization on the capacitor for years.[41]

Blood sugar energy harvesting[عدل]

Another way of energy harvesting is through the oxidation of blood sugars. These energy harvesters are called Biofuel cells. They could be used to power implanted electronic devices (e.g., pacemakers, implanted biosensors for diabetics, implanted active RFID devices, etc.). At present, the Minteer Group of Saint Louis University has created enzymes that could be used to generate power from blood sugars. However, the enzymes would still need to be replaced after a few years.[42]

Tree metabolic energy harvesting[عدل]

Tree metabolic energy harvesting is a type of bio-energy harvesting. Voltree has developed a method for harvesting energy from trees. These energy harvesters are being used to power remote sensors and mesh networks as the basis for a long term deployment system to monitor forest fires and weather in the forest. Their website says that the useful life of such a device should be limited only by the lifetime of the tree to which it is attached. They recently deployed a small test network in a US National Park forest.[43]

Future directions[عدل]

Electroactive polymers (EAPs) have been proposed for harvesting energy. These polymers have a large strain, elastic energy density, and high energy conversion efficiency. The total weight of systems based on EAPs is proposed to be significantly lower than those based on piezoelectric materials.

Nanogenerators, such as the one made by Georgia Tech, could provide a new way for powering devices without batteries.[44] As of 2008, it only generates some dozen nanowatts, which is too low for any practical application.

Noise harvesting NiPS Laboratory in Italy has recently proposed to harvest wide spectrum low scale vibrations via a nonlinear dynamical mechanism that can improve harvester efficiency up to a factor 4 compared to traditional linear harvesters.[45] قالب:Contradict

See also[عدل]

References[عدل]

[46]

  1. ^ Holst Centre Human++ Program
  2. ^ Pickin’ up good vibrations to produce green electricity
  3. ^ Piezoelectric Energy Harvesting Research at NTU
  4. ^ Some Energy Harvesting Research @NUS
  5. ^ Noise in Physical Systems Laboratory
  6. ^ EnHANTs project at Columbia University
  7. ^ "Architectures for Vibration-Driven Micropower Generators, P. D. Mitcheson, T. C. Green, E. M. Yeatman, A. S. Holmes"
  8. ^ ik, batterij by Erick Vermeulen, NatuurWetenschap & Techniek January 2008
  9. ^ Energy Harvester Produces Power from Local Environment, Eliminating Batteries in Wireless Sensors
  10. ^ http://www.idtechex.com/research/reports/wireless-power-transmission-for-consumer-electronics-and-electric-vehicles-2012-2022-000281.asp
  11. ^ Inventor Joe Tate's Ambient Power Module converts radio frequencies to usable electrical power (albeit only milliwatts) sufficient to operate clocks, smoke alarms, Ni-Cd battery chargers, &c.
  12. ^ Electronic Device Which is Powered By Actuation Of Manual Inputs, US Patent no. 5,838,138
  13. ^ Knee-Mounted Device Generates Electricity While You Walk, By Chad Skelton, 7 Feb 2008
  14. ^ Soccer ball generates and stores electricity while you play
  15. ^ energy harvesting industrial realisations
  16. ^ Zhong Lin Wang's nanobrushes
  17. ^ VIBES Project
  18. ^ Electricity from the nose
  19. ^ Millimter-scale piezoelectric energy harvester
  20. ^ "Japan: Producing Electricity from Train Station Ticket Gates"
  21. ^ Powerleap tiles as piezoelectric energy harvesting machines
  22. ^ "Commuter-generated electricity"
  23. ^ "Energy Scavenging with Shoe-Mounted Piezoelectrics"
  24. ^ MEMS power generator with transverse mode thin film PZT
  25. ^ Ultra-wide bandwidth piezoelectric energy harvesting
  26. ^ F.Y. Lee, A. Navid, and L. Pilon (2012). Pyroelectric waste heat energy harvesting using heat conduction. Applied Thermal Engineering, vol. 37, no. 1, pp. 30–37.
  27. ^ [www.tandfonline.com/doi/abs/10.1080/00150198108209595 R.B. Olsen, D.A. Bruno, J.M. Briscoe, and W.F. Butler (1981). A pyroelectric energy converter which employs regeneration. Ferroelectrics, vol. 38, no. 1-4.]
  28. ^ R.B. Olsen, D.A. Bruno, and J.M. Briscoe (1984). Cascaded pyroelectric energy converter. Ferroelectrics, vol. 59, no. 3-4, pp. 205–219.
  29. ^ H. Nguyen, A. Navid, and L. Pilon (2010). Pyroelectric energy converter using co-polymer P(VDF-TrFE)and the Olsen cycle for waste heat energy harvesting. Applied Thermal Engineering, vol. 30, no. 14-15, pp. 2127–2137.
  30. ^ R.C. Moreno, B.A. James, A. Navid, and L. Pilon (2012). Pyroelectric Energy Converter For Harvesting Waste Heat: Simulations versus Experiments. International Journal of Heat and Mass Transfer, Vol. 55, pp. 4301-4311.
  31. ^ J. Fang, H. Frederich, and L. Pilon (2010). Harvesting nanoscale thermal radiation using pyroelectric materials. ASME Journal of Heat Transfer, vol. 132, no. 9, pp. 092701.
  32. ^ R.B. Olsen, D.A. Bruno, and J.M. Briscoe (1985), “Pyroelectric conversion cycle of vinylidene fluoride-trifluoroethylene copolymer”, Journal of Applied Physics, vol. 57, no. 11, pp.5036–5042.
  33. ^ A. Navid and L. Pilon (2011), “Pyroelectric energy harvesting using Olsen cycles in purified and porous poly(vinylidene fluoride-trifuoroethylene) thin films”, Smart Materials and Structures, vol. 20, no. 2, pp. 025012.
  34. ^ F.Y. Lee, S. Goljahi, I. McKinley, C.S. Lynch, and L. Pilon (2012), “Pyroelectric waste heat energy harvesting using relaxor ferroelectric 8/65/35 PLZT and the Olsen cycle”, Smart Materials and Structures, vol. 21, no. 2, pp. 025021.
  35. ^ "Pyroelectric Energy Scavenger"
  36. ^ Fraunhofer Thermogenerator 1
  37. ^ 15mW thermogenerator by Fraunhofer Gesellschaft
  38. ^ Tellurex Corporation
  39. ^ CSIRO FIED
  40. ^ Tremont Electric nPower PEG
  41. ^ http://tikalon.com/blog/blog.php?article=2011/electret
  42. ^ The power within, by Bob Holmes, New Scientist, 25 August 2007
  43. ^ "Voltree's Website"
  44. ^ Georgia tech Nanogenerator
  45. ^ Noise harvesting
  46. ^ http://www.esoftwall.com/2011/09/document-on-integrated-solar-energy.html

External links[عدل]


تصنيف:Microtechnology Energy harvesting